The Allen Bradley 1756-M02AS is a synchronous serial interface, or SSI, servo module. It is an analog servo interface module that has 2 axes available. Up to 32 axes of the 1756-M02AS module can be installed in a controller. This module has been optimized for control of drives or actuators that require +/-10V velocity or torque reference input. The 1756-M02AS module has an SSI position feedback output and is a cost-effective option for open-loop or closed-loop motion control of devices that support an analog motion interface. This module is compatible with a wide range of quadrature output rotary and linear transducers. SSI devices available are rotary absolute and incremental encoders, linear absolute and incremental encoders, linear laser distance, linear absolute glass scales, and linear magnetostrictive. You can use either the cage clamp 1756-TBCH or spring clamp 1756-TBS6H RTB for this module. It has two types of servo loops: torque and velocity/hydraulic. The torque has a PID with velocity feedforward position loop and its velocity loop is PI with Accel feedforward (nested) and with directional scaling and friction compensation. The velocity has a position loop of PID with velocity feedforward and accel feedforward with directional scaling and friction compensation. The velocity loop is not applicable, as it is handled by the drive or valve. The 1756-M02AS module has a gain resolution of 32-bit floating point and an absolute position range of 4,294,967,296 transducer counts. It has a selectable rate of 500Hz, 666.7Hz, 1kHz, 2kHz, and 4kHz and an update period of 250µsec, 500µsec, 1msec, 1.5msec, and 2msec. Its resolution ranges from 8 to 31 bits and it has an isolated 5V differential electrical interface (RS-422 signal). It also has an input impedance of 215 ohm differential and an output load of 100 ohm minimum. It has a clock frequency of 205kHz or 625kHz and the transducer can either be binary or gray code. It is an optically isolated, current sinking module. The 1756-M02AS module has a nominal input voltage of 24V DC, an off-state maximum voltage of 8.5V DC, and an on-state voltage that ranges from 17V DC to 26.4V DC. It has a current draw of 700 mA and 2.5 mA at 5.1V DC and 24V DC respectively. It also has a power dissipation of 5.5 W, a thermal dissipation of 18.77 BTU/hr, and an isolation voltage of 30V that is continuous from user to system.

The Allen Bradley 1756-M02AS is a Motion interface module. This module is specifically an analog motion module, used for open loop and closed loop motion applications. This module comes with a built-in support for 2 motion axes – however, additional module may be installed if needed, to provide up to 32 axes of motion axes per ControlLogix processor.

The 1756-M02AS supports Torque Position and Velocity loop. With position loop, Proportional + Integral + Derivative (PID) with velocity feed-forwards is utilized while for Velocity loop. Proportional + Integral (PI) with accel feed-forwards is used including directional scaling and friction compensation capability. This module may also control Position loop of velocity or hydraulic drive. With this, a combine function of Position and Velocity is used where PID with velocity feed-forwards and accel feed-forwards with directional scaling and friction compensation is utilized.

The 1756-M02AS has a gain resolution of 32-bit floating point value with absolute position range of 232 (4,294,967,296) transducer counts with user configurable rate of 500 Hertz, 666.7 Hertz, 1 Kilohertz, 2 Kilohertz, and 4 Kilohertz. It is a single slot module that directly mounts to any available slot of the ControlLogix chassis. Compatible 1756 chassis for this module include the 1756-A4, 1756-A7, 1756-A10, 1756-A13, and 1756-A17. It requires use of a 1756-TBCH or 1756-TBS6H Removable Terminal Block (RTB) for wiring of signals. It also supports the ControlLogix standard power supply (1756-PA72/C, 1756-PA75/B, 1756-PB72/C, 1756-PB75/B, 1756-PC75/B, 1756-PH75/B) and ControlLogix redundant Power supply (1756-PA75R, 1756-PB75R, 1756-PSCA2).

The 1756-M02AS’s input type is Synchronous Serial Interface (SSI) input with a resolution of 8-31 bits. The input interface of this module has a rated isolation of Isolated 5V differential (RS-422 signal) with a clock frequency of 208 Kilohertz or 625 Kilohertz. It uses a Binary or Gray code transducer. It also has a Registration input that supports Current sinking circuit with optical isolation. Similarly, other input types for this module also support current sinking configuration with optical isolation as well.

 

Request a Quote now or call us at 1-800-755-2883 for expert assistance.

TCI Supply is not an authorized Allen Bradley Distributor

Specification Sheet .pdf

 

Manufacturer Rockwell Automation
Part Number/Catalog No. 1756-M02AS
Voltage Range ±10V dc
Servo output Type Analog Voltage
Registration input Optically isolated, current sinking input
Motion input Synchronous Serial Interface (SSI)
Rate 500 Hz, 666.7 Hz, 1 kHz, 2 kHz, 4 kHz
Absolute Position range 232 (9 4,294,967, 296)
Gain Resolution 32- bit floating point
Servo Loop Torque: Position and Velocity Loop Velocity or Hydraulic: Position loop
Brand Allen Bradley
Analog output resolution 16 bits
Series 1756 ControlLogix
Module Type Analog Servo Interface
Discrete outputs Solid-state isolated relay contacts
Discrete output operating voltage 24VDC, Nominal.
Axes per Module 2
Axes per Controller 32
Backplane Current (5Volts) 700 milliamps
Backplane Current (24Volts) 2.5 milliamps
Power Dissipation 5.5 Watts
Removeable Terminal Blocks 1756-TBCH, 1756-TBS6H
Current Draw (5.1 Volts) 1.2 amps
Power Dissipation 6.2 Watts
Thermal Dissipation 21.2 BTU-hour
Isolation Voltage 50 Volts Continuous
Enclosure None

 

 

Get A Quote

Fill in the form below, or call us now at 1-800-755-2883

"*" indicates required fields

This field is for validation purposes and should be left unchanged.

Full Product Catalog

See our comprehensive product catalog!